Paiva, João Luís Monney de SáRodrigues, Joel Ribeiro2017-02-062017-02-062016-12-192016-10-28http://hdl.handle.net/10400.19/4399Este trabalho teve como objetivo o dimensionamento, construção e estudo de um permutador de calor a aplicar numa caldeira doméstica de 20 kW, alimentada a peletes. Pretendeu-se com a aplicação daquele, realizar um pré-aquecimento da água, concretamente antes de entrar na caldeira, através do arrefecimento dos fumos e condensação de parte do vapor de água, transformando a caldeira numa caldeira de condensação. Numa primeira fase, realizaram-se alguns ensaios à caldeira, nas condições à saída de fábrica, para recolher informações acerca do seu funcionamento. Destes ensaios, em primeiro lugar, retiraram-se conclusões sobre a sua eficiência térmica (na ordem dos 50 a 60 %). Em segundo lugar, obtiveram-se as informações necessárias para o dimensionamento do permutador, como sejam, caudal mássico de água, caudal mássico de fumos, temperatura da água na entrada da caldeira, temperatura dos fumos na saída da caldeira e concentração volúmica dos constituintes dos fumos. Numa segunda fase, procedeu-se ao referido dimensionamento. Este, feito de forma iterativa, e considerando a operação da caldeira em três cargas de funcionamento diferentes, à carga baixa (P1), média (P3) e máxima (P5). Dimensionou-se um permutador capaz de arrefecer os fumos e de conseguir realizar parte da condensação do vapor de água, um permutador compacto de feixe de tubos escalonados e alhetados. Com esta introdução, esperava-se o aumento da eficiência térmica da caldeira para valores na ordem dos 90 %, em cada uma das cargas. Em terceiro lugar, procedeu-se ao fabrico do permutador, realizado nas oficinas do departamento de Engenharia Mecânica do IPV. Esta dividiu-se por duas etapas: a primeira, o corte dos materiais (tubos e alhetas); a segunda, a montagem dos tubos e alhetas. Em quarto lugar, o permutador construído foi aplicado na caldeira e realizaram-se vários ensaios, nas diferentes cargas, de forma a avaliar tanto o funcionamento daquele como da caldeira, bem como a tirar conclusões acerca da variação do rendimento térmico da caldeira após aplicação do permutador. No final dos ensaios, verificou-se que o permutador, embora com uma eficiência aquém do que se esperava (cerca de 40 a 50 %), fez com que o rendimento da caldeira tivesse aumentado para valores em volta dos 80 %. Um estudo simples, apresentado no final desta tese, acerca da viabilidade da aplicação deste permutador permitiu concluir que se conseguiriam economizar entre 600 a 800 kg de peletes por ano (ao preço dos peletes à data, representava uma economia de 100 a 130 €/ano).ABSTRACT: This study aimed to design, construction and study of a heat exchanger to apply in a domestic pellet boiler of 20 kW. The intention with the application thereof, to perform a preheating of the water, particularly before entering the boiler, through the cooling of the smoke and condensation of the water vapor, transforming the boiler in a condensing boiler. Initially, there were some trials to the boiler, on conditions at the plant output, to collect information about its operation. Of these trials, first, withdrew conclusions on its thermal efficiency (in the order of 50 to 60%). Secondly, there were obtained the necessary information for the design of the heat exchanger, such as, water mass flow, mass flow of vapor, water temperature in the boiler inlet, temperature of the flue gases in the boiler exit and volume concentration of the constituents of flue gas. In a second phase, it proceeded to said sizing. This made iteratively, and considering the boiler operation in three different operating loads, the low load (P1), medium (P3) and maximum (P5). A scaled-exchanger can cool the smoke and accomplish the condensation of the water vapor, a compact exchanger bundle of finned tubes and staggered. With this introduction, it was hoped to increase the thermal efficiency of the boiler to values of around 90% in each of the loads. Third, it proceeded to the manufacture of the heat exchanger, made in the workshops of the Mechanical Engineering department of IPV. This was divided in two stages: first, the cutting of materials (tubes and fins); the second assembly of tubes and fins. Fourthly, the built exchanger was used in the boiler and were performed various tests on different loads in order to evaluate both the function thereof as the boiler, and to draw conclusions about the variation of the thermal efficiency of the boiler after application of exchanger. At the end of the tests, it was found that the heat exchanger, but with an efficiency below the expected (about 40 to 50%), made the boiler efficiency had increased to values around 80%. A simple study, presented at the end of this thesis, on the feasibility of applying this exchanger concluded that if they could save between 600 to 800 kg of pellets per year (the price of pellets to date, representing a saving 100-130 €/year ).porCaldeira domésticaPermutador de calorCondensaçãoEficiência EnergéticaPeletesEstudo, projeto e teste experimental de um permutador de calor para recuperação da energia contida nos gases de exaustão de uma caldeira domésticamaster thesis201605201